Furnace Installation & Replacement in Salt Lake City, UT

We replace gas furnaces after a load calculation and a duct and venting inspection, so the new furnace is sized to the house rather than to the old cabinet.

A furnace replacement is a sizing decision, a venting decision and a duct decision wearing a box. Get the size wrong and the house cycles and never feels even; get the venting wrong and the furnace locks out on cold nights; ignore the duct and the new unit inherits the old unit’s airflow problem. Salt Lake City houses run 5,154 heating degree days a year (NOAA), so those mistakes get exercised every winter.

Why Choose Us for Furnace Installation in Salt Lake City

The size comes from a load calculation

Replacing like for like copies the original builder's guess, and builders oversized for decades. A room-by-room load calculation sizes the furnace to the house as it is now, including insulation, windows and duct losses. An oversized furnace short cycles, runs cold duct air and wears out faster.

Venting is chosen for the house, not the catalogue

An 80 percent furnace vents into a flue; a condensing furnace vents in PVC and produces condensate. At 4,579 feet (USGS) combustion air and draft need attention, and a shared masonry chimney left over from an older install often decides which category is possible.

The duct system is measured, not assumed

A furnace can only deliver what the ducts allow. Static pressure and temperature rise tell you whether the existing duct can carry the new unit's airflow, and whether a return has to be added. Skipping that step is how a good furnace gets a bad reputation.

Commissioning is a checklist with numbers

Gas pressure, temperature rise, static pressure, combustion and condensate are set and recorded at the end, not assumed. Those readings are what a warranty call and the next technician both need, and they are the difference between installed and installed correctly.

whatsapp image 2026 04 21 at 11.55.24 am.jpeg

Why Furnace Replacement Can't Wait in Salt Lake City

The January normal low at Salt Lake City International is 24.2 degrees Fahrenheit and the airport averages 51.9 inches of snow a season (NOAA 1991-2020 normals). A furnace that is limping into that stretch is being asked to carry the whole house through the coldest weeks of the year, and the failure usually lands on the coldest night rather than on a convenient weekday.

There is a safety reason as well. Furnaces at the end of their life are the ones most likely to have a failing heat exchanger, and a cracked exchanger puts combustion gas into the airstream. Replacing on a schedule lets the venting and the gas line be designed; replacing in an emergency means working around whatever is there.

The practical cost of waiting is choice. A planned replacement can wait for the right size and the right venting category. An emergency replacement takes what is available that day, which is often the wrong size in the right cabinet. That is the outcome a planned replacement exists to avoid, and it is why the assessment happens in September.

Finally, there is the inspection. A replaced furnace is inspected, and an inspection on a thirty-year-old installation often turns up venting or gas work nobody planned for. Knowing that before the furnace is ordered is what keeps the job to one week.

heating ventilation and air conditioning (1)

WHAT A REPLACEMENT INVOLVES

Proof: What a Furnace Installation Covers Here

A furnace replacement is six decisions that have to agree with each other: how much heat the house needs, how the furnace modulates, how it vents, how the duct carries the air, how the gas and electrical supply feed it, and how it is commissioned. Get one wrong and the other five compensate badly. Three quarters of Salt Lake City’s occupied homes heat with utility gas (ACS 2023, B25040), and roughly forty-eight percent of the housing predates 1970, so most replacements here are a modern furnace going into a system designed around a much simpler one. The six blocks below are the decisions in the order we settle them, and each one is recorded so the next person who opens the cabinet knows what was decided and why.

Load Calculation and Furnace Sizing

Sizing starts with a room-by-room heat loss calculation, not with the square footage of the house and not with the output of the furnace being removed. The calculation accounts for insulation, window area and orientation, air leakage, duct location and the design temperature for this climate. Getting it right matters because an oversized furnace heats the house too fast, satisfies the thermostat early and leaves cold spots, while running short cycles that wear the heat exchanger. An undersized furnace runs continuously on the coldest nights and never quite catches up. The number that matters is the output at design conditions, and it is a calculation rather than an opinion. We keep the calculation with the installation record, because it is what a warranty discussion and the next technician both need.

Single-Stage, Two-Stage and Modulating Furnaces

The furnace's control strategy decides how the house feels as much as its size does. A single-stage furnace runs at full fire or nothing, which is fine in a tight, well-insulated house and less pleasant in an older one with uneven rooms. A two-stage furnace runs long and low most of the time and steps up when needed, which gives steadier temperatures and quieter operation. A modulating furnace varies its fire continuously and pairs well with a variable-speed blower. The right answer depends on the house, the duct and how the occupants use the space, and it is worth deciding before the model number is chosen. A modulating furnace on a duct that cannot carry low airflow is money spent on a feature the house never sees.

Eighty Percent Versus Condensing Venting

An 80 percent furnace vents combustion gas up a flue, usually a metal liner or an existing chimney. A condensing furnace extracts more heat by cooling the gas until water condenses, which means PVC venting, a condensate trap and a drain. At 4,579 feet (USGS) the thinner air affects draft and combustion, and a shared masonry chimney can be too large for a single appliance to warm, which is why an orphaned flue often pushes a replacement toward condensing. The venting category also decides where the furnace can sit, because a condensing unit needs a route to a sidewall and a drain for the water it produces. The termination height has to clear the snow line, which in this valley is not a formality.

Ductwork, Static Pressure and Airflow

A furnace is only as good as the duct it is attached to. Static pressure measured at the supply and return tells you whether the existing duct can move the airflow the new furnace needs, and a high reading means the blower is working against a restriction that will shorten its life and raise the temperature rise. Undersized returns, long flex runs and closed-off registers are common in older homes, and adding a return is often the cheapest efficiency work in the house. Replacing a furnace without measuring the duct is how a homeowner ends up with a new unit that behaves exactly like the old one. The measurement takes minutes and it is the cheapest part of the job.

Gas Supply, Electrical and Condensate

A gas furnace needs the right inlet pressure and a gas line sized for its input, and a condensing unit needs a drain that will not freeze. Electrical requirements vary with the blower: a variable-speed motor draws differently from a PSC motor, and an older circuit may need attention. We check the meter capacity, the gas line size, the circuit and the disconnect, and the condensate route before the furnace is ordered. A condensing furnace draining to an exterior wall is a winter failure waiting to happen, and rerouting it is much easier before the cabinet is in place. An older panel sometimes needs a dedicated circuit for a variable-speed blower as well, and a disconnect within sight of the furnace is not optional.

Commissioning, Combustion and the Permit

Commissioning is where an installation becomes a working system: gas pressure set to the manufacturer's specification, temperature rise measured against the rating plate, static pressure recorded, combustion analysed, condensate flowing and the thermostat configured for the equipment. Those numbers are written down and left with the furnace. Replacement is also permit work in the valley, where the Greater Salt Lake Municipal Services District lists furnace replacement and Salt Lake City runs its own mechanical permit process, so the inspection is scheduled as part of the job. The commissioning readings are also what proves the installation was set up for this altitude rather than for sea level. Those readings are also the first place a warranty claim is checked, so they protect the homeowner as much as the installer.

THE LOCAL SCENARIO

The Scenario Nobody Covers: Replacing Into a 1963 Duct System

The median Salt Lake City house was built in 1963 and about forty-eight percent of the stock predates 1970 (ACS 2023). Those houses were built with a furnace and a duct system designed together for a much smaller cabinet, and the replacement has to live with both.

The first constraint is physical: the old furnace sits in a closet or a crawlspace with a flue connection at a fixed height, and the new cabinet may be taller, wider or shorter. The second is the duct: a 1963 trunk and branch system was sized for a furnace moving less air than a modern unit, and it often has one central return. The third is venting, because the masonry chimney that served the original furnace may now be orphaned or oversized.

The result is that a replacement in these homes is really three jobs: a furnace swap, a duct correction and a venting decision. The houses where it goes smoothly are the ones where all three were measured before the order. The houses where it goes badly are the ones where the furnace was chosen first and the duct was discovered later, usually by the homeowner, in January. Measuring the trunk, the returns and the flue before the order is what turns three jobs into one scheduled one, and it is the part of the work the homeowner can watch.

What that means in practice is a short list of questions answered before the order: what size does the calculation call for, how does the furnace vent, what does the duct actually move, and what has to change for the three to agree. A replacement planned that way is unremarkable, which is exactly what a heating system should be.

repair of a gas boiler 2026 03 24 06 07 35 utc scaled.jpg

What Our Furnace Installation Covers

Gas Furnace Replacement

Like-for-like where the venting and duct allow it, with the load calculation and temperature rise checked rather than assumed.

High-Efficiency Condensing Furnaces

PVC venting, condensate routing and combustion set for altitude, with the drain kept inside the building envelope.

Two-Stage and Modulating Upgrades

Steadier temperatures and quieter operation where the duct can support the lower airflow, with the control wiring and thermostat matched to the equipment.

Duct and Return Corrections

Static pressure measured, restricted returns added or resized, and the airflow set so the new furnace can actually deliver its rated capacity.

Venting and Chimney Work

Flue liners, orphaned chimney corrections, sidewall terminations clear of snow level, and combustion air sized for the room.

AREAS WE SERVE

Furnace Installation Across Salt Lake City and the Valley

We replace furnaces along the Wasatch Front, from the Avenues and Sugar House to West Jordan, Herriman and Layton. The housing era decides the work: pre-1970 homes bring duct and flue corrections, newer homes bring condensing venting and condensate routes.

The load calculation

Room-by-room heat loss at the design temperature, so the furnace is sized to the house rather than to the old cabinet.

The duct assessment

Static pressure, return capacity and register count measured before the equipment is chosen, because the duct sets the real airflow.

The venting decision

Flue, liner or sidewall, with the combustion air path and the altitude derating accounted for.

The gas and electrical check

Meter capacity, line size, circuit and disconnect, and the condensate route if the furnace condenses.

The installation

Old furnace removed and hauled away, new cabinet set, venting and drain completed, and the gas connection tested.

The commissioning record

Gas pressure, temperature rise, static pressure and combustion recorded and left with you, plus the permit inspection scheduled.

Call (385) 486-0176 before the old furnace quits. HVAC Company Salt Lake City will run the load calculation, measure the duct and settle the venting question before anything is ordered.

Salt Lake City

West Valley City

Murray

Millcreek

Holladay

Cottonwood Heights

Sandy

Midvale

West Jordan

South Jordan

Draper

Riverton

Layton

Salt Lake City HVAC — Frequently Asked Questions

The replacement questions we answer most often in Salt Lake City, in the order they usually come up.

It is not a homeowner job. A furnace involves gas piping, combustion air, venting, electrical work, a heat exchanger and a permit, and a mistake in the venting path is a carbon monoxide risk rather than a leak. Replacement is also permit work in the valley, with an inspection attached, and an unpermitted install surfaces at a sale.

Usually yes, on safety and reliability rather than efficiency alone. At thirty years the heat exchanger is the concern, and a failed exchanger means the furnace should not run. Parts availability also becomes a problem, so a repair can leave the house waiting on a component that is no longer made.

Fifteen to twenty years is the usual range, with the low end common where the filter is neglected and the duct is restricted. A furnace past fifteen years that needs a blower and a control board is usually at the point where replacement is the better answer.

Not always, but it needs the existing duct measured. If static pressure is high or the return is undersized, a new furnace will underperform on the old duct. Adding a return or correcting a restriction is often enough, and it is cheaper than replacing the whole system.

In the valley, yes: the Greater Salt Lake Municipal Services District lists installing or replacing a furnace as permit work, and Salt Lake City Building Services runs its own application process through the Citizen Access Portal, with mechanical permits separate from the building permit. Requirements are address-specific, so confirm with Building Services before work starts.

Sometimes, and it is the first thing measured. Modern cabinets vary in height and width, and the flue connection height and the door clearance decide whether a like-for-like swap is possible. Where it is not, a shorter cabinet or a different venting category solves it, but that has to be known before the furnace is ordered.

For whole heating systems beyond the furnace itself, see heating installation & replacement in Salt Lake City.