Heating Installation & Replacement in Salt Lake City, UT
We design and install heat pumps, furnaces, boilers and ductless systems, starting from a load calculation and the distribution that is already in the house.
Replacing a heating system is a design decision before it is an equipment decision: how much heat the house loses at design conditions, how that heat is distributed, and what the electrical service can carry. In Salt Lake City the answer is not automatic, because three quarters of homes burn gas and nearly a quarter heat with electricity (ACS 2023), and the valley runs 5,154 heating degree days a year (NOAA).
Why Choose Us for Heating Installation in Salt Lake City
The design temperature is the starting point
Equipment is selected against the outdoor design temperature for this valley, not a national average. A heat pump sized for a mild climate will lean on its backup for weeks here, and a boiler sized on floor area alone will short cycle all winter. The calculation is the difference between a design and a guess.
Backup heat is planned, not improvised
Every cold-climate heat pump here needs a plan for the coldest nights, whether that is electric strip, a gas furnace in a dual-fuel setup or a staged approach. The plan decides the electrical load and the controls, so it is settled before the order.
The distribution is assessed with the equipment
Ducts, baseboard, radiant loops and radiators all have limits. Installing a new heat source on distribution that cannot deliver is how a good system gets a bad reputation, and it is why the assessment covers both.
Commissioning is measured and left with you
Airflow, refrigerant charge, water temperature and static pressure are set and recorded. Those readings are what prove the system was designed for this house rather than merely connected to it, and they are what a warranty call is checked against.

Why Heating Replacement Can't Wait in Salt Lake City
The January normal low at Salt Lake City International is 24.2 degrees Fahrenheit, the airport averages 51.9 inches of snow a season, and the valley logs 5,154 heating degree days against 1,420 cooling degree days (NOAA 1991-2020 normals). A heating system here is not a seasonal convenience; it is the machine the house depends on for months.
An aging system fails in the season it is worked hardest, and a replacement then has to be arranged under pressure. The design work that makes a replacement good, load calculation, distribution assessment, electrical check and permit, all take time, and none of it happens well in an emergency.
There is a safety dimension too. A boiler with a failing section, a furnace with a cracked exchanger or a heat pump with a failing compressor all reach a point where the honest answer is replacement. Reaching that point in October is a project; reaching it in January is an emergency with a space heater in it. The system that is seven years past its expected life is the one worth planning around, not the one that still works today. Planning also lets the electrical and duct work happen in the same visit.

WHAT A REPLACEMENT INVOLVES
Proof: What a Heating Installation Covers Here
A heating installation is a design problem in six parts: how much heat the house needs, what makes that heat, what backs it up on the coldest nights, how the heat is distributed, what the electrical service can supply, and how the finished system is proven. The six blocks below are those parts in the order we settle them. The mix of systems in this valley makes the order important, because a house moving from gas to a heat pump changes the electrical load, the distribution temperature and the backup strategy at the same time. Each block is a decision with a measurement behind it, and each one is recorded so the next technician inherits a design rather than a guess.
Cold-Climate Heat Pump Sizing and Capacity
A heat pump is selected on its capacity at the outdoor design temperature, not on its nominal tonnage. Capacity falls as the outdoor air gets colder, and a unit that is generous in October can be marginal in January, which is why the manufacturer's extended performance data is read at the design temperature rather than at a mild rating point. The load calculation and the capacity curve are compared directly, and the difference is what backup heat has to cover. In this valley the design temperature is low enough that the comparison matters on almost every job, and a heat pump chosen without it will run continuously through the coldest weeks while the house slowly loses ground. Sizing also affects comfort: an oversized unit short cycles and dehumidifies poorly in summer, while an undersized one never catches up.
Backup Heat: Strip, Gas or Dual Fuel
Every heat pump in this climate needs a plan for the hours when its capacity and the house's load diverge. Electric resistance strip is the simplest backup, and it is expensive to run but cheap to install, which is why it is common. A dual-fuel system keeps a gas furnace as the second stage and switches to it below a set outdoor temperature, which suits a house that already has gas service and ductwork. The choice decides the electrical load, the controls and the switchover temperature, so it is made with the load calculation in hand. A heat pump installed with no coordinated backup, or with backup that never stages in, is a comfort complaint waiting for the first cold snap.
Condensing Boiler Replacement
A modern condensing boiler extracts heat from the flue gas by cooling it until water condenses, which means it needs a drain, a proper vent and a return water temperature low enough to condense. That last point is the one that decides whether the efficiency is real: a condensing boiler piped into high-temperature baseboard may never condense at all. Replacement work includes the near-boiler piping, the expansion tank, the air eliminator and the controls, and often a look at whether the emitters can run cooler. Combi boilers add domestic hot water to the same cabinet, which changes the sizing question because the boiler now has to satisfy a shower as well as a heating load. On a replacement, the near-boiler piping is where most of the quality lives.
Ductless Mini-Split Systems
A ductless system puts a head in the room it heats, which solves rooms that a duct system never served: additions, basements, garages and second floors. The design question is how many heads, where they go and whether one outdoor unit can carry them with the diversity the house actually uses. Line set length, elevation and flare quality decide whether the system holds its charge for years, and condensate routing decides whether a ceiling head stains a ceiling. Ductless is also the practical answer for a house with no duct and no room for one, and it is a poor answer when the house already has a duct system that only needs correction. The number of heads matters less than where they sit and how the outdoor unit is loaded.
Hydronic Distribution and Radiant
On a boiler system the emitters are part of the design, not an afterthought. Cast-iron radiators, baseboard and radiant slabs each want a different water temperature, and a condensing boiler performs best when it can run low. Replacement is the moment to fix a loop that was never balanced, add a manifold actuator that works, or separate zones that were combined for convenience. Radiant floors need a mixing valve and a manifold that can be controlled per loop, and a system that was installed without one will overheat the slab and underheat the room next to it. Distribution work is the unexciting half of a heating replacement and the half that decides whether the new boiler ever reaches its rated efficiency.
Electrical Service, Load and Commissioning
Heat pumps and electric backup change the electrical load on a house, and an older panel may not have the capacity for both. The service is checked against the new load before the equipment is ordered, because upgrading a panel is a project of its own. Commissioning closes the job: refrigerant charge verified by superheat or subcooling, airflow set, water temperature confirmed, controls configured and the switchover temperature tested. Those readings are recorded and left with the system. Heating replacement is also permit work in the valley, with the Greater Salt Lake Municipal Services District listing furnace and boiler replacement and Salt Lake City running its own mechanical permit process, so the inspection is scheduled as part of the job.
THE LOCAL SCENARIO
The Scenario Nobody Covers: Moving a 1963 House Off Gas
The median Salt Lake City house was built in 1963, and roughly forty-eight percent of the stock predates 1970 (ACS 2023). Those houses were built around a gas furnace, a gas water heater and a masonry chimney, and a household that wants to move to a heat pump is changing three systems at once.
The first question is the electrical service, because a cold-climate heat pump with electric backup can need more capacity than the panel was built for. The second is the duct, because a heat pump moves more air at a lower temperature than a gas furnace, and a 1963 trunk and branch system often cannot. The third is the venting: the chimney that served the furnace and water heater becomes surplus, and the water heater’s flue may need to change with it.
None of that makes the conversion a bad idea. It makes it a design project rather than an equipment swap, and the houses where it goes well are the ones where the panel, the duct and the flue were assessed before the heat pump was ordered. The ones where it goes badly are the ones where a unit was installed and the duct was discovered later. The conversion is worth doing; it just has to be designed as one project rather than three sequential purchases. The houses that go smoothly are the ones where the panel, the duct and the flue were measured together, which is also the cheapest order to do the work in.

What Our Heating Installation Covers
Cold-Climate Heat Pump Installation
Capacity matched to the design temperature, backup staged properly, and the distribution checked for the lower supply temperature.
Gas Furnace Replacement
Load-calculated sizing, venting chosen for the house, and the duct measured so the new furnace can deliver its rated airflow.
Boiler and Hydronic Replacement
Condensing boilers with near-boiler piping, expansion and air control, and emitters assessed for the lower water temperature.
Ductless Mini-Split Installation
Heads placed for the rooms that need them, line sets and flares done properly, and condensate routed where it cannot stain a ceiling.
Electrical and Controls Upgrades
Service capacity checked against the new load, thermostats and zoning configured, and the switchover temperature tested rather than assumed.
AREAS WE SERVE
Heating Installation Across Salt Lake City and the Valley
We install heating systems along the Wasatch Front, from the Avenues and Sugar House to West Jordan, Herriman and Layton. Older homes bring hydronic and duct corrections; newer ones bring heat pump conversions and zoning.
The load calculation
Room-by-room heat loss at the design temperature, which decides both the equipment size and the backup strategy.
The distribution assessment
Duct static pressure, baseboard output or radiant loop condition, measured before the heat source is chosen.
The electrical check
Service capacity, panel space and circuit requirements for a heat pump and its backup, confirmed before the order.
The venting and flue
What stays, what changes and what becomes surplus when a gas appliance comes out, including the water heater's flue.
The installation
Old equipment removed, new system set, refrigerant or water connected, controls wired, and the site left clean.
The commissioning record
Charge, airflow, water temperature and switchover recorded and left with you, plus the permit inspection scheduled.
Call (385) 486-0176 before the heating season turns. HVAC Company Salt Lake City will run the load calculation, check the distribution and the electrical service, and design a replacement that fits this house.
Salt Lake City
West Valley City
Murray
Millcreek
Holladay
Cottonwood Heights
Sandy
Midvale
West Jordan
South Jordan
Draper
Riverton
Layton
Salt Lake City HVAC — Frequently Asked Questions
The replacement questions we answer most often in Salt Lake City, across heat pump, furnace, boiler and ductless systems.
Usually yes. At thirty years the heat exchanger is the safety concern, parts become hard to source, and the efficiency loss is real. A replacement also lets the venting and the duct be corrected at the same time, which a repair does not.
A straightforward replacement of an existing system is usually a day or two. A conversion that adds backup heat, upgrades the electrical service or corrects ductwork takes longer, and the assessment is what tells you which one you are buying.
A cold-climate heat pump works through most of a Salt Lake City winter, and it needs backup for the coldest nights. The valley's January normal low is 24.2 degrees, with colder nights regularly, so the design has to include capacity at that temperature and a backup that stages in properly.
Not usually, but the emitters decide how low the boiler can run. Cast-iron radiators and baseboard both work with a condensing boiler, and the system performs best when the water temperature can be kept low. Where the emitters cannot run cool, the boiler still works but gives up some of its efficiency advantage.
In the valley, yes: the Greater Salt Lake Municipal Services District lists installing or replacing a furnace, boiler, heat pump and water heater as permit work, and Salt Lake City Building Services runs its own application process through the Citizen Access Portal, with mechanical permits separate from the building permit. Confirm for your address before work starts.
On the house rather than on preference: the electrical service, the duct, the existing gas service and the distribution temperature all narrow the choice. A house with good ducts and capacity for a heat pump is a strong candidate; a house with a marginal panel and high-temperature baseboard may be better served by a high-efficiency furnace or a dual-fuel design.
Considering a heat pump instead of a conventional heating system? See heat pump installation & replacement in Salt Lake City, including dual-fuel systems.
